In conclusion, the microstructure of WC–12Co changed with the addition of Mo + B 4 C and showed a trend with increasing addition of Mo + B 4 C.
Excerpts
Both figures suggest that the influence of the time of dissolution of a nanoparticle in mineral oil may be significant.
The bending moment–axial force interaction curve has an outward curvature, which implies an increasing trend up to a peak and a decreasing trend up to zero.
The overlay with the influence of MnS inclusions might be significant.
The change of these parameters for the different rolling conditions exhibits an increasing trend with respect to the decrease in the number of voids ( Figure 6 ).
In the case of M SL , pit depth has portrayed a decreasing trend with the increase in A MF .
Conversely, PP/PS/MWCNT systems exhibited an increasing trend for the storage modulus as a function of the annealing time, indicating that the presence of nanotubes effectively prevented coalescence; further measurements performed after the thermal treatment demonstrated the rebuilding of the CNT network structure, through the Brownian motion of the nanofillers into the melt.
tanδ showed a decreasing trend with increasing the nanofiller content, revealing a progressively more pronounced elastic-like response for the nanocomposites and a gradual fluid–solid transition, which was associated with a gelation phenomenon occurring in the system.
As indicated by Table 4 , the wear depth and grinding crack width exhibited an increasing trend with an increase in the normal load.
An increasing trend of ES versus temperature was proven, reaching a plateau value by observing the evolution of stabilization versus time.
As presented in Table 5 , the cross-section of deformed fibers exhibits a decreasing trend with temperature.
It can be observed from Figure 4 a,b that as the temperature rose, the thermal conductivity of both the composite and aerogel showed an increasing trend.
The experimental data were applied to evaluate linear, quadratic, and cubic models, and results indicated that the quadratic model was highly significant and suitable to represent the response of the RB4 dye removal.
Figure 9 presents the results of the bee phase area measured using Image-Pro Plus software 6.0 (Media Cybernetics Corporation, Rockville, MD, USA), in which the bee phase areas of the three asphalt mastics with different F/A ratios were less than that of the base asphalt binder and exhibited a decreasing trend with an increase of the F/A ratio.
In this study, an increasing trend in the metal concentration leachate was observed for fired clay bricks with the increase in CB content from 0% to 2% by mass.
This may be due to the usage of the stabilizer and the fiber inclusion that helps in lowering the dry density of the soil and the ability of the stabilizer to absorb a large amount of water, as for lime and alkaline activation; An increasing trend of the soil percentage loss was observed with the increase of the wetting/drying cycles for both soil stabilization treatments with an accumulation of 3% to 5% increment, except for the first cycles of treatment with lime.
The increase in mechanical properties of mortar containing GSA with a decreasing trend in hardened density was determined.
However, the capacity of the pyrolyzed CNC electrode ( Figure 8 a) showed an increasing trend, and remained stable during 300 cycles, while that of the CNC–SnO 2 NF800 electrode decreased rapidly during the first 100 cycles and showed a capacity of 284 mA h g −1 , similar to that of the pyrolyzed CNC electrode after 300 cycles (276 mA h g −1 ).
Therefore, the observed difference is quite significant. 3.3.
reported that the decrease in the crystal size was highly significant even at the lower Mg percentage, and crystal size decreases with the increase in Mg concentration up to 35 atomic percentage in respect of the total metal ions.
With the increase of the graphene doping amount, the bulk density of SiC ceramics showed a trend of gradual decrease.
The room temperature magnetic properties exhibited that Co doped GNMSs are ferromagnetic in nature and an increasing trend in magnetism was observed with increasing Co contents.
A particular source of variation may be significant if the calculated F value at a certain confidence level is greater than the tabulated F value at the same confidence level.
An increasing trend in the size of the deformation zone by up to four times its original pore size is reported at a higher feed rate and lower cutting speed [ 18 ].
However, many other parameters, like temperature, pH, potential difference and impurities are highly significant.