Excerpts

The variation in effective modulus is shown in Figure 6 b, where a decreasing trend can be observed as the array number in the Z direction increases.

When the applied axial strain increases, the twist angle per axial strain also shows an increasing trend.

In the low-energy region (E < 0.1 MeV), a clear trend is observed, wherein higher Fe content correlates with increased MAC values.

The flexural strength of the geopolymer mortar showed a decreasing trend with the continual increase in the waterglass modulus.

A clear trend can be seen in the τ u to ρ tot graph ( Figure 9 a), where the increase in maximum stresses is accompanied by an increase in the reinforcement ratio.

We did not find such a clear trend, however, in samples tested at 77 K.

Water Absorption As illustrated in Figure 2 , the water absorption capacity of fly ash-based autoclaved aerated aggregates (FAAs) exhibits a decreasing trend at both 1 h and 24 h intervals with the augmentation of cement content.

p -values of responses 1 to 6 were 0.028, 0.01, 0.003, 0.023, 0.002, and 0.026 are less than 0.05, indicating that the model is highly significant [ 86 ].

With the increase in PAM doping, the fluidity of cement mortar shows a decreasing trend.

However, when the content exceeds 15%, a decreasing trend becomes apparent.

With the increase in CPO@SiO 2 -1.0T concentration, the SOD activity showed a decreasing trend, reaching the lowest value at 0.1 mg/mL.

From Figure 11 , it can be observed that with the increase in curing period, the UCS of Groups A, B, and C all exhibited an increasing trend.

Moreover, quite significant differences in the course of the 2,4-D adsorption isotherms should be noted, especially in the area of lower concentrations for the three tested fractions.

The results indicated a positive trend in the enhancement of mechanical properties as the filler concentration increased.

It can be seen from Table 4 that with the increase in normal stress, the slope of the straight line shows a decreasing trend, indicating that the shear strength increases with the rise of normal stress, and the correlation coefficients are 0.93, 0.96, 0.98, 0.99, and 0.90, respectively, indicating that there is a good correlation between the parameters.

As illustrated, all samples showed a decreasing trend in cumulative intrusion with the curing age, regardless of the DG content.

Specifically, as shown in Figure 12 , specimens such as the plain sample, CFDG05, and CFDG10 showed a clear trend in which larger pores decreased while finer pores increased over time.

The relative error in DVC measurements exhibited a decreasing trend from F1 to F5, indicating surface stabilization as machining advanced.

Compressive Strength Under Different Temperatures From the CVT curve in Figure 9 , it can be seen that the compressive strength shows a decreasing trend at 24 °C–100 °C and an increasing trend at 100 °C–300 °C, and the compressive strength at 300 °C is greater than that at normal temperatures.

At the same age of hydration reaction, with the increase in sodium aluminate content, the amorphous material content shows a decreasing trend.

For the SOEC cathode channels with aspect ratios of 0.25 and 1, the temperature distribution is relatively uniform, exhibiting an increasing trend, with the peak temperature occurring at the outlet of the cathode channel.

However, an unexpected trend was observed, where samples with 15% infill density exhibited higher tensile strength compared to those with 20–25% infill.

The dwell time in the water bath [s] has a p -value of 8.5 × 10 −7 , indicating a highly significant effect in statistical terms.

As demonstrated in Table 6 , the flexural tensile strength of SFP materials exhibits an increasing trend with extended curing durations.

Conversely, the retarding effect of XANa (PX) shows a decreasing trend, and at 0.15%, it demonstrates a pro-setting effect, reducing the initial setting time by around 79%.