Excerpts

The microhardness exhibited first increases and then changes to a decreasing trend with the scanning speed.

Analysis of Corrosion Rate V corr In Scheme 4 , a clear trend of lower corrosion rates can be observed in elements that have not experienced any loss of reinforcement (yellow dots), and the carbonation coefficients tend to be higher, following the same trend as discussed in previous figures.

As the shear rate increased, the viscosities of the samples all showed a decreasing trend, indicating shear-thinning flow behavior.

The influence of the impact strength of biocomposites with fiber filler on the quality of products may be significant, especially in the context of products that are exposed to dynamic loads, such as impacts or vibrations.

The difference, although quite significant, is not statistically significant at the 0.01 level of significance due to the large scatter of partial results, which is typical for brittle materials.

When the coarse aggregate content ranges between 20% and 30%, the strength loss shows a decreasing trend.

With the further increase in the quenching temperature, the hardness of the test steel showed a decreasing trend.

An interesting trend was observed: as the SHI fluence increased, an additional PL signal with a maximum at 1.7 eV was detected.

It can be seen that the AlSi12 electrode-coated surfaces ( Figure 4 b,c) are more uniform and smoother than those of the NW electrode ( Figure 4 f and also that with increasing pulse energy, the roughness and surface irregularities show an increasing trend.

The results obtained for the b e -value, which is akin to the I b -value, consistently displayed a decreasing trend, transitioning from 4 to 1 under tensile-loading conditions.

Although the calculated enthalpies of formation reveal an expected trend, their values are underestimated with respect to the data given in tables published by Knacke et al.

When the fiber content was greater than 0.25%, the deformation modulus and tensile modulus showed a decreasing trend.

We identified an increasing trend in the adsorption capacity with an increasing V micro /V external ratio.

Almost no weight loss was observed before 372.86 °C, but a rapid weight loss occurred in the range of 372.86–424.53 °C due to dehydroxylation of CH; thereafter, weight loss proceeded moderately before 559.21 °C, and then became a little significant in the temperature range of 559.21–689.62 °C due to dehydroxylation of kaolinite, and finally turned to be mild until 1050 °C due to volatilization of some matters in HACG.

However, there is only a weak trend (rs = −0.20).

When looking at the relative compressive strength as a function of the non-clay phases in the raw clay (see Figure 5 , right), it becomes visible that for a low substitution level, the content has a low impact on the reactivity, whereas with a rising substitution, a clear trend of decreasing relative compressive strength with increasing content of non-clay phases can be seen.

There is an apparent trend indicating an increase in quasi-static stress levels with a decrease in wave propagation velocity ( Figure 14 b).

A section highlighting correlative imaging and complimentary techniques for SIMS is given to note an increasing trend in the use of SIMS in correlative metal analysis.

Furthermore, the corresponding change in length (ΔL/L) at the isothermal stage of every step shows a decreasing trend with the extension of isothermal time.

For conditions at 100% f z , a clear trend cannot be identified.

Furthermore, given that finding a relationship between scaffold geometry and mechanical properties is a goal, it can be observed that Young’s modulus has an increasing trend with increasing thickness.

The characteristic of femtosecond lasers, known as “cold processing”, is highly significant in micro and nanofabrication, as it effectively reduces thermal diffusion while processing.

Contrarily, the MRR demonstrated an increasing trend when a NaNO 3 electrolyte was used.

Conversely, when using a NaNO 3 electrolyte, the side gap showed a decreasing trend, whereas the front machining gap demonstrated an increasing trend, with an increase in laser power.

With the increase in crosslinking agent content, the number of cells in SRF gradually increases, and the overall size of the cells shows an increasing trend.