Excerpts

However, T x has a decreasing trend with the increased Mg content.

With the increase in wheel speed, the peak grinding temperature showed a trend of a small increase and then a decrease.

Osteoblasts showed an increasing trend in the scaffolds and pore plates of all groups, and the number of cells reached the highest on day 5 ( Figure 8 A).

Interestingly, with the increase in the refractive index n , the sensitivity and FOM of the three Quasi BICs all illustrated an increasing trend, which verified that the interaction between the medium around the metasurface and the electric field is enhanced with the increase in the refractive index n .

At the same GFS content, with the increase in the specific surface area of the GFS powder, the total hydration heat release and hydration heat release rate showed an increasing trend.

However, the degree of crystallinity showed an increasing trend via a decreasing FWHM.

The Δ E j -a j curve has a Z-shape, with a monotonically decreasing Δ E j -a j curve before the EPB point and a monotonically increasing Δ E j -a j curve after the EPB point until the FS point when it starts to show a decreasing trend.

By calculating the average Ca/Si ratios of the gel phase (see Table 5 ), it was found that with the increase in the slag content, the average Ca/Si exhibited an increasing trend up to 0.7581.

Moreover, the difference between the instantaneous and long-term moduli is quite significant, implying that different penetration efficiency can be obtained by adjusting the insertion speed, i.e., with a higher insertion speed, more efficient penetration can be achieved because the apparent Young’s modulus value should increase with compression speed. 4.

Specifically, as the load increases, the kinetic coefficient of friction of the composite coating shows a decreasing trend, which is the opposite of the behavior in the general metal friction-wear test.

As shown in Figure 9 b, with an increase in filler content, R b showed a trend of increasing first and then decreasing; that is, there was an optimal filling ratio of 0.3 wt.% for the f-GO nanosheet in RTV.

Upon considering the overall combined effect of various parameters, a clear trend emerges.

With the further increase in the quenching temperature, the hardness of the test steel showed a decreasing trend.

An interesting trend was observed: as the SHI fluence increased, an additional PL signal with a maximum at 1.7 eV was detected.

It can be seen that the AlSi12 electrode-coated surfaces ( Figure 4 b,c) are more uniform and smoother than those of the NW electrode ( Figure 4 f and also that with increasing pulse energy, the roughness and surface irregularities show an increasing trend.

The results obtained for the b e -value, which is akin to the I b -value, consistently displayed a decreasing trend, transitioning from 4 to 1 under tensile-loading conditions.

Although the calculated enthalpies of formation reveal an expected trend, their values are underestimated with respect to the data given in tables published by Knacke et al.

When the fiber content was greater than 0.25%, the deformation modulus and tensile modulus showed a decreasing trend.

With the same initial moisture content and freeze–thaw cycles, a clear trend developed: the lower the root content, the more prominent the reduction in the cohesion of the root-soil composite during the freeze–thaw cycles.

It should be noted, however, that this strengthening of the material, related to partial hardening, is accompanied by a simultaneous and quite significant reduction in ductility.

Such chain modifications as shown in Figure 8 via reaction A gradually promote network heterogeneity, resulting in a decreasing trend of both the modulus and tensile strength. 3.6.

The results show a decreasing trend in adsorption capacity (Pb > Cd > Cu > Ni) according to obtained values (i.e., q m = 169, 132, 84.0, and 60.7, respectively, for Pb, Cd, Cu, and Ni).

Although high-crystallinity graphite also produces 2D peaks, the position of the 2D peak in few-layer graphene shows a clear trend of moving towards a lower wave number (blue shift phenomenon) [ 24 , 25 , 26 , 27 ].

The pore size shows an increasing trend with the increase in DG.

Accordingly, this is consistent with the result in Figure 12, showing that the ratio of the loss modulus to the storage modulus increases with temperature from 0 to 25 °C, which means that the hardness will show a decreasing trend following an increase in temperature.