“a decreasing trend”

The storage modulus values under wet conditions showed a decreasing trend with increasing temperature.

Figure 2 g presents that the properties of bidirectional trading relationships between economies in the international crop trade networks were stable after 2016 but showed a decreasing trend after the first quarter of 2022.

In contrast, the obtained k TOC values for TOC removal during AC photodegradation with Y 2 TmSbO 7 under dynamic conditions exhibited a decreasing trend across the cycles, with values of 0.0114 min −1 , 0.0107 min −1 , 0.0101 min −1 , 0.0096 min −1 , and 0.0091 min −1 .

Therefore, considering that the western region is close to the optimal scale, while the central eastern region shows a decreasing trend, the overall technical efficiency shows a slow fluctuation and upward trend.

The activity of SOD and CAT showed a decreasing trend in yellow needles, indicating a weakened ability of yellow needles to eliminate the reactive oxygen species produced during plant metabolism ( Figure 1 ).

At the same time, the ACC was higher when there were one and two aggregation layers, but showed a decreasing trend as the aggregation layers increased.

Conversely, a decreasing trend was noted for the 95% ethanol extract.

The results showed a decreasing trend with delayed treatment initiation ( Figure 8 ), suggesting that the best antiviral effects are assured with treatment administered shortly after (2 h) infection. 2.2.3.

While no significant differences were observed between the two irradiation doses, a decreasing trend in viability can be seen at the higher dose in all but one sample.

Meanwhile, for natural and semi-synthetic opioids prescribed by in-state doctors, a decreasing trend was more visible, notably in chain pharmacies.

divergens NHT2-5 showed a decreasing trend, while the TVC of loin samples inoculated with P. taetrolens NLJ3 displayed an increasing trend.

Using the one-way ANOVA test, we obtained that CRC patients had statistically significant higher values of NEU, NLR, PLR, and CRP, which increased in the three stages, while LMR, ALB, and PNI showed a decreasing trend. 2.5.

The relative abundance of all three bacterial genera showed a decreasing trend during BBP-meju fermentation and further decreased with increasing salt concentration ( Figure 7 c).

Similarly, a decreasing trend in a* and b* values was observed in the preparation of noodles from germinated wheat compared to ungerminated wheat [ 29 ]. 3.1.3.

Except for Central Latin America, Central Asia, and Southern Sub-Saharan Africa, all regions had a decreasing trend in ASMR (Fig. 1 b).

We sought to evaluate whether a decreasing trend of serum BDG was associated with lower mortality and to investigate the goodness of BDG downslope cutoff values in predicting clinical outcome, in critically ill patients affected by proven invasive candidiasis.

The DDDs(Defined Daily Doses) of EAMs (LPGs) showed a decreasing trend since 2016 and rose again in 2019.

The results show that, with the increase in frequency, the single-pulse discharge energy decreases continuously, and the coating thickness shows a decreasing trend, from the highest value of 152 μm at 400 Hz to the lowest value of 87.5 μm at 1000 Hz.

On the other hand, although the total manufacturing time of the theoretical WAAM tooling also following a decreasing trend with the reduction in design over-thicknesses, this most favourable case still requires a total manufacturing time three times longer than pure machining tooling.

Under other working gaps, the minimum magnetic field strength shows a decreasing trend.

As shown in Figure 4 b,c, the suspension ratios of three kinds of fibers exhibit a decreasing trend as the sedimentation time increases.

The average coefficient of friction values after running-in, from 20 m to 100 m, showed a decreasing trend, as follows: μ = 0.455 for quenched and tempered DIN 16MnCr5 steel, μ = 0.413 for gas-nitriding, μ = 0.376 for pack boriding, and the lowest value of friction, μ = 0.365, for duplex gas-nitriding and pack boriding when compared to quenched and tempered DIN 16MnCr5 steel.

On the other hand, the paste with 0.2% SAP B (D-17B) showed a higher increase in plastic viscosity, reaching 0.45 Pa·s at 5 min, followed by a decreasing trend, with a slight increase observed between 20 min and 35 min, ranging from 0.24 Pa·s to 0.33 Pa·s, compared to the reference mix, which ranged from 0.22 Pa·s to 0.18 Pa·s.

In the polypropylene fiber dosage of more than 0.6%, the compressive strength of mortar with the increase in fiber dosage is a decreasing trend, which may be due to the fiber dosage being too much, the mortar mixing not being uniform, the fiber being easy to agglomerate inside the mortar, and the formation of weak points, leading to the compressive strength of the mortar being reduced.

With the increase in immersion time, the main frequency band of low frequency gradually disappears, and the main frequency of the acoustic emission signal increases, indicating that long-term immersion will lead to a decreasing trend in the development scale of rock fractures.