Excerpts

(2) The damping properties of FCTPs show an increasing trend with the increase in excitation amplitude and temperature values.

The coupling wear showed a trend to increase with the degradation of the polyethylene inlay, as can be seen in Figure 7 c; the Spearman’s rank-order correlation coefficient r s amounted to 0.49 ( p < 0.01).

The L size group showed a trend of greater migration along medial-lateral (x-axis) direction and in the anterior-posterior direction (z-axis) than the other head–neck length groups ( Figure 6 ).

For the further axial load levels, the curvature showed a decreasing trend, since the concrete crushing in the extreme compression fiber governed the yield condition.

Their study also indicated that the while yield curvature had an increasing trend with the amount of longitudinal reinforcement, the yield curvature decreased with the concrete strength, regardless of the yielding condition.

The thickness of the plates is not obviously different, but the measurements reveal a definite trend in nanoscale dimension.

Radiation Since the skeletal sand mold can reach a high temperature, the radiation among the irregular surface itself may be significant.

The p -values of P and V are both less than 0.01, which indicates that their influences both on the RD and the SR are highly significant.

Interestingly there is no increase in collagen deposition over 21 days in the GM group but an increasing trend in deposition is seen following the addition of osteocyte secreted factors.

This error may be significant depending on the estimated MC, from 10% to 50% of the average value in the range from 25% to 5% MC.

We found that the index of refraction of Fe-Ni co-doped ZnO thin films assumed an increasing trend and attained a value of 2.20 for 8% Fe-Ni co-doped ZnO thin films.

In ACN samples there is a significant trend toward decreasing surface areas with increasing rigidity and electron density of the cross-linker ( Table 1 , Figure 1 b).

Amongst the present molecules with monofunctional phenyl groups, an overall trend indicates an increase in φ as the fluoro-based group pivots from the para position inwards to the ortho placement (see Table 2 ).

MAPC of IBC Si cell shows a decreasing trend with the thickness of the front ITO, in respect of the increased reflection and free carrier absorption, and meanwhile it shows local maxima around the distinct CdS thickness, defined by the QWOT at the absorption onset wavelength of the top cell absorber.

It can be seen that the maximum packing density shows a decreasing trend with decreasing maximum particle size, which is logical seen the decreased polydispersity of the particles.

In view of the fact that it is a quite significant defect, an attempt was made to find the reasons for this phenomenon and to examine its effect on the degradation process. 3.1.

In conclusion, the microstructure of WC–12Co changed with the addition of Mo + B 4 C and showed a trend with increasing addition of Mo + B 4 C.

Both figures suggest that the influence of the time of dissolution of a nanoparticle in mineral oil may be significant.

The bending moment–axial force interaction curve has an outward curvature, which implies an increasing trend up to a peak and a decreasing trend up to zero.

Conclusions (1) The flow curves of nano-SiCp/Al-Si composites showed a trend of peaking first and then decreasing gradually with the increase in strain variables, and the stress value was significantly affected by deformation temperature and strain rate.

The experimental results of the wind tunnel test showed an increase of the lift/drag ratio of about 83.98% achieved with a flap deflection angle of 20°, which is a highly significant gain with respect to flight efficiency.

The negative sign in Equation (1) means that the rate of change in the macrotexture height exhibits a decreasing trend.

On the contrary, being able to standardise with composite resin replicas, the results here presented were extremely homogeneous and with a clear trend in the results.

A decreasing trend of protein cluster count, which corresponds to a decrease in the thickness of the lubrication film, is found in all experiments.

Furthermore, MCL in position 1 (3.5 mm) is about 5 to 8 μm lower than in the other two positions (5.5 mm and 7.5 mm) for each shear rate, with a slight trend to higher differences for low shear rates.