Excerpts

At present, there has been an increasing trend for biomimetic nano-HA to be used as a preventative agent for oral care products [ 17 ].

At all energies, the MFP have an increasing trend with the Bi 2 O 3 content.

Springback induced variations on tube thickness and cross-section flattening are discussed: the thickness variation during springback is attributed to the elastic unloading induced deformation and the cooling induced thermal deformation, which is small and neglectable; the maximum cross-section flattening decreases first and then presents an increasing trend, while it increases with the increase of the bending angle.

Wurtzite, in particular, exhibited a quite significant distortion due to viscous collapse of the bottom layers (see lower part of Figure 8 b).

In recent decades, a significant trend has been observed concerning recycling or reusing solid waste materials in highway pavements, which can be categorized into pavement by-products, industrial by-products, and waste produced by the construction and demolition of buildings and road infrastructure [ 6 , 7 , 8 , 9 ].

In the same direction, in response to external influences, both the compressive strength and the compressional wave velocity of concrete have a decreasing trend after sulfate erosion.

Meanwhile, Bacteroidetes, Firmicutes and Chloroflexi in four treatments showed a decreasing trend.

The evolution of depth of erosion over the complete period of acid exposure did not show a clear trend, suggesting that the process of erosion is more-or-less completed after seven days of exposure. 3.4.3.

In each case, a positive trend is observed: as impact energy increases, the average microstructural measures increase concurrently.

As can be seen from Figure 18 and Figure 19 , when the consolidation pressure increases, the consolidation coefficient of CRFS shows an increasing trend.

Similarly, if there is less inclination, then it has very slight significance, so in our case, the sliding speed has slight significance.

However, with an increase in tempering temperature from 630 to 670 °C, the diffusion of carbon in martensite leads to the decrease in carbon content in martensite; as a result, the tensile strength and yield strength show a decreasing trend.

According to the calculations in Table 2 , the residual stresses in the nickel plating show an increasing trend as the texture coefficients of the crystal plane (111) increases.

Although in this case the use of the HiPIMS coating did not produce a significantly better machined surface quality, when compared to the dc MS-obtained coated tool, the increase in wear resistance is quite significant.

The temperature of the system rises rapidly, due to a violent thermite reaction, and the energy released by the jet shows an increasing trend; there is an impact intensity threshold, so that the jet release energy reaches the upper limit. energetic jets impact loading energy release molecular dynamics multi-scale pmc-status-qastatus 0 pmc-status-live yes pmc-status-embargo no pmc-status-released yes pmc-prop-open-access yes pmc-prop-olf no pmc-prop-manuscript no pmc-prop-legally-suppressed no pmc-prop-has-pdf yes pmc-prop-has-supplement no pmc-prop-pdf-only no pmc-prop-suppress-copyright no pmc-prop-is-real-version no pmc-prop-is-scanned-article no pmc-prop-preprint no pmc-prop-in-epmc yes pmc-license-ref CC BY 1.

The reductions in wear are quite significant for lubricant applications, since low wear rate values enhance the useful life of machine components.

Fibers between 12–14 and 11–13 in tension and compression, respectively, suffer from a decreasing trend in reverse T- and VR-zones.

The yield stress and the plastic viscosity mainly show a decreasing trend with the increase of the parameters except SS/SH ratio.

The results of the preliminary research by the authors suggest that the thermal effect of this process on the material cut may be significant.

They distinctly identified the need to fabricate high-performance hybrid aluminium composites and reported that the mechanical properties particularly the tensile strength improves up to a certain extent, i.e., 3 to 5 wt.% of SiC; however, beyond this range, the tensile strength showed a decreasing trend.

Our study found no significant change but a slight trend of reduction on the hindfoot eversion and forefoot abduction.

From the figures, the modulus and strength properties all exhibited a decreasing trend as the void content increased.

Similarly, the F40 series specimens exhibited a decreasing trend in slump values, varying from 195 mm to 160 mm.

Two types of behavior can be seen here: first, a decreasing trend at lower frequencies, and then an increasing trend at higher frequencies.

In addition, when OSP mass content was kept constant, the slope in the rising part (O–A) indicated an increasing trend for specimens in each group as curing time increased. 4.2.