Excerpts

On the contrary, in terms of ranking of the binders, a clear trend linked to GNP content cannot be observed from the University of Minnesota results ( Figure 8 ).

The results of these experiments have high confidence level, which show that different patterns and pattern-changing effects are highly significant.

Porosity The porosity of the specimen showed an increasing trend as the temperatures, as seen in Figure 10 .

These two factors led to quite significant differences in the luminescence properties of the EuPOM and EuPOM incorporated in the PMO framework.

The results revealed a decreasing trend in height and diametric shrinkage with the increase in CB content.

An increasing trend in both the compressive and specific strengths was shown with the incorporation of fiber, except for the concrete containing solely polypropylene fiber.

At higher holding times of 120 and 240 min, the values are higher compared to 60 min, but the variations are hardly significant.

With the content of CHPs increasing, the strength of mortar showed a decreasing trend, while the pore-filling efficiency and strength healing rate of mortar were further improved.

Additionally, the temperature of the first stage of deformation (1100 °C) was 50 °C higher than in the case of tests performed in the single-stage compression of the tested steels, while on the basis of these test results a clear trend could be seen that, along with the increase in deformation temperature at a constant rate of plastic deformation, in this case 10 s −1 , the critical crush value decreased from 0.253 to 0.183 for X98 steel and from 0.279 to 0.163 for X105 steel.

With the increase of temperature, the content of liquid phase showed an increasing trend.

For the lowest Hf substitution, the β-phase bulk modulus (B β ) is 121 GPa, with a decreasing trend reaching 116 GPa for 25 at.% Hf.

The value decreased from −24,417.19 to −34,376.63 J/mol, which indicates a clear trend in the process.

The following conclusions can be drawn from Figure 12 : (1) With an increasing head pressure of the 30% fine-grained samples, the porosity of the samples in the same area shows an increasing trend from layer to layer.

Through a comparative analysis, we have determined the following: (1) The total number of pores in the 30% fine-grained sample shows a decreasing trend during the seepage process.

The presented studies show a clear trend of the impact of voltage increase on the obtained nanomechanical properties.

The addition of methanol causes a current decrease of ≈ 49% when Pt/C is used; however, for Co/S 3 N 2 –GF and Mn/S 3 N 2 –GF, its influence is almost insignificant, leading to current retentions of 90% and 95%, respectively.

(2) The damping properties of FCTPs show an increasing trend with the increase in excitation amplitude and temperature values.

In ACN samples there is a significant trend toward decreasing surface areas with increasing rigidity and electron density of the cross-linker ( Table 1 , Figure 1 b).

Amongst the present molecules with monofunctional phenyl groups, an overall trend indicates an increase in φ as the fluoro-based group pivots from the para position inwards to the ortho placement (see Table 2 ).

MAPC of IBC Si cell shows a decreasing trend with the thickness of the front ITO, in respect of the increased reflection and free carrier absorption, and meanwhile it shows local maxima around the distinct CdS thickness, defined by the QWOT at the absorption onset wavelength of the top cell absorber.

It can be seen that the maximum packing density shows a decreasing trend with decreasing maximum particle size, which is logical seen the decreased polydispersity of the particles.

In view of the fact that it is a quite significant defect, an attempt was made to find the reasons for this phenomenon and to examine its effect on the degradation process. 3.1.

In conclusion, the microstructure of WC–12Co changed with the addition of Mo + B 4 C and showed a trend with increasing addition of Mo + B 4 C.

Both figures suggest that the influence of the time of dissolution of a nanoparticle in mineral oil may be significant.

The bending moment–axial force interaction curve has an outward curvature, which implies an increasing trend up to a peak and a decreasing trend up to zero.