Excerpts

In Figure 8 , the defects of GNPs showed a trend of rising first and then falling as the temperature increased.

The original grain size of ZK60 BM is relatively small and the abnormal growth of the recrystallized grains is slightly significant, so that the final grain size of ZK60 in SZ is slightly larger than that of the original ZK60 BM.

The reason may be significant differences in ferrocene oxidation and poly [Ni(salcn)] in the second step.

The p -values of n , v f , a e and a p in the F regression model are less than 0.001, showing that the four experimental factors have extremely significant effects on the cutting force.

These BCPs were related to the N···O interactions and had quite high values of electron density as well as Laplacian and energy density at the critical point so their influence on the crystal packing could be quite significant.

For the ∑5 (36.9°/<100>) GBs, as sin( θ ) increases from 0 to 1, the GBE of β -Ti at 1300 K shows a decreasing trend, which is opposite to the variation trends of GBE for W at 2400 K, as shown in Figure 7 a,b.

Subsequently, the hydraulic conductivity is dominated by the gradient of suction, showing an increasing trend in the low suction range.

The results displayed that the activation energy had an increasing trend with the increase in the lignin compared to the virgin asphalt.

The fluidity showed a trend of first increasing and then decreasing with the addition of SF when the w/c ratio was 0.5, 0.6.

The yield stress of the paste in the second period still showed an increasing trend, and the increase was greater than in the first period.

The effect of sliding speed on the value of Ih is reduced at the low P and becomes almost insignificant at P = 1 MPa ( Table 3 ).

While a clear trend in the evolution of the interfacial strength and the rolling temperature was registered for the magnesium–aluminium interface, a less clear trend was registered for the other interface.

The content of α*-fiber shows an increasing trend, and {411}<148> and {100}<120> reach 14.6% and 6.88% as recrystallization was completed at 700°, respectively.

However, the tensile properties, particularly the E b showed an increasing trend with increasing the HAP concentration.

The high fitting degree shows that there is a highly significant linear correlation between σ p and ε ̈ c .

As the magnetic fields increase, the ΔS−T curve changes from the symmetrical herringbone to the asymmetric curve, indicating that the alloy phase transition type from the secondary phase transition to the primary phase transition and ΔS shows an increasing trend (because the primary phase transition is the change of material magnetic ordered state caused by lattice distortion, the resulting magnetic entropy change is much greater than the secondary phase transition and reaches values of 9.45 J/(kg·K) upon an applied field of 1.5 T). 4.

The maximum isothermal magnetic entropy change mutated after 20 min of heat treatment, and then showed an obvious trend of first increasing and then decreasing, and reached the maximum value after 2 h of heat treatment.

However, this paste showed the most rapid increase in BET surface area, as a significant difference was apparent even after the first 30 min and especially after one hour, i.e., between the initial and final setting time indicated by the Vicat needle (see Table 2 ), as well as between 60 and 120 min.

Since typical conversion of CO 2 to carbonate is very slow and inefficient under the conditions of ambient temperature and pressure, there has recently been an increasing trend in research on maximizing the mineral carbonation reaction using supercritical CO 2 .

Its effect on surface temperature is quite significant during the day but at night, due to low heat capacity of the plaster layer, the stored heat is quickly lost and the temperature rises only slightly.

From the experimental results obtained, the following conclusions can be drawn: The fresh properties of the developed mixes showed a decreasing trend with the increases in silica fume and RCA and with the inclusion of steel fibres.

According to Figure 9 a the OP-TMF life of the reference material, Esshete 1250, does not show a clear trend when the material is aged before OP-TMF testing.

In addition, OC (3rd column in Table 4 ) shows a clear trend, as it increases when the amount of SFG increases.

In contrast, the softening point showed a decreasing trend.

The MOE of CFRBs shows a decreasing trend when the content of TBC decreases.